The file_contains_line helper function was not testing whether a file
exists or not prior attempting to read from it.
Add this check to circumvent errors on the private WiFi config in
case the hwflags file is missing.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
d666ebcaa3 ubus: update to the latest version
a9100f2196 base-files: wifi: tidy up the reconf code
b27b63b082 base-files: wifi: swap the order of some ubus calls
6f13a39035 mac80211: print an error if wifi teardown fails
9302e63d1a mac80211: always call wireless_set_data (FS#3784)
bea9380149 mac80211: fix no_reload logic (FS#3902)
ccbe535604 mac80211: backport fix for nl80211 control port tx (fixes FS#3857)
4c29ff7cb8 mac80211: add support for 802.3 encap offload with software rate control
a078037ace mac80211: improve rate control performance
9fa925362f busybox: sysntpd: add trigger to reload server
a75928d125 busybox: sysntpd: option to bind server to iface
Signed-off-by: David Bauer <mail@david-bauer.net>
The relevant entry for the primary MAC location was lost when rebasing
the patch on OpenWrt 21.02.
Fixes commit ded4b8a711 ("rockchip-armv8: add FriendlyARM NanoPi R2S")
Signed-off-by: David Bauer <mail@david-bauer.net>
The OpenWrt routing feed was moved to the OpenWrt GitHub org.
Update the URL, as the old one might not work in the future.
Signed-off-by: David Bauer <mail@david-bauer.net>
Configure a radio for HE (802.11ax) operation in case it's supported by
the hardware. This can be the case for 2.4 GHz as well as 5 GHz.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
e16a45f258 iwinfo: update to latest Git HEAD
0c51b265bf iwinfo: update to latest Git HEAD
85cef1cf22 kernel: bump 5.4 to 5.4.128
e171d11f55 libusb: Fix parsing of descriptors for multi-configuration devices
3d62b5d5c6 base-files: fix /tmp/TZ when zoneinfo not installed
3047df2317 base-files: fix zoneinfo support
ab5010d170 exfat: update to 5.12.3
72d93c1ba4 realtek: Fix failsafe mode
7a5a247c1f base-files: failsafe: Remove the VLAN modifier from interface name
c0fdfd15fc base-files: failsafe: Fix IP configuration
98b1a6435f kernel: Backport patch to automatically bring up DSA master when opening user port
ec780bdb92 kernel-5.4: backport latest patches for wireguard
82c700de67 hostapd: fix handling of the channel utilization options
1247a6bb35 bcm4908: fix Ethernet broken state after interface restart
25daa921da bcm4908: add kmod-gpio-button-hotplug
74dbf3412b base-files: fix typo in config_generate MAC check
125deb4d78 base-files: set MAC for bridge ports (devices) instead of bridge itself
e410ef8389 hostapd: wolfssl: add RNG to EC key
f6d8c0cf2b wolfssl: always export wc_ecc_set_rng
56228e9393 ath79: don't autodetect AR8033 PHY capabilities
2e157714a8 build,json: fix generation with empty profiles
8add3e139c build: preserve profiles.json between builds
All targets now use OpenWrt device abstraction. Thus, all targets now
can be built using a per-device RootFS.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer