-- This is an example site configuration for Gluon v2014.4 -- -- Take a look at the documentation located at -- http://gluon.readthedocs.org/ for details. -- -- This configuration will not work as it. You're required to make -- community specific changes to it! { -- Used for generated hostnames, e.g. freifunk-abcdef123456. (optional) -- hostname_prefix = 'freifunk-', -- Name of the community. site_name = 'Freifunk Entenhausen', -- Shorthand of the community. site_code = 'ffxx', -- Prefixes used within the mesh. Both are required. prefix4 = '10.xxx.0.0/20', prefix6 = 'fdxx:xxxx:xxxx::/64', -- Timezone of your community. -- See http://wiki.openwrt.org/doc/uci/system#time_zones timezone = 'CET-1CEST,M3.5.0,M10.5.0/3', -- List of NTP servers in your community. -- Must be reachable using IPv6! ntp_servers = {'1.ntp.services.ffxx'}, -- Wireless regulatory domain of your community. regdom = 'DE', -- Wireless configuration for 2.4 GHz interfaces. wifi24 = { -- Wireless channel. channel = 1, -- ESSID used for client network. ssid = 'entenhausen.freifunk.net', -- Specifies the channel width in 802.11n and 802.11ac mode. -- Possible values are: -- HT20 (single 20MHz channel), -- HT40- (2x 20MHz channels, secondary below) -- HT40+ (2x 20MHz channels, secondary above) htmode = 'HT20', -- Adjust these values! mesh_ssid = 'xe:xx:xx:xx:xx:xx', -- ESSID used for mesh mesh_bssid = 'xe:xx:xx:xx:xx:xx', -- BSSID used for mesh -- Bitrate used for multicast/broadcast packets. mesh_mcast_rate = 12000, -- (optional) mesh VLAN on 802.11 ad-hoc interface (1-4095) -- mesh_vlan = 14, -- client_disabled = true, -- mesh_disabled = false, }, -- Wireless configuration for 5 GHz interfaces. -- This should be equal to the 2.4 GHz variant, except -- for channel and htmode. wifi5 = { ssid = 'entenhausen.freifunk.net', channel = 44, htmode = 'HT20', mesh_ssid = 'xx:xx:xx:xx:xx:xx', mesh_bssid = 'xx:xx:xx:xx:xx:xx', mesh_mcast_rate = 12000, -- mesh_vlan = 14, -- client_disabled = true, -- mesh_disabled = false, }, -- The next node feature allows clients to always reach the node it is -- connected to using a known IP address. next_node = { -- anycast IPs of all nodes ip4 = '10.xxx.0.xxx', ip6 = 'fdxx:xxxx:xxxx::xxxx', -- anycast MAC of all nodes mac = 'xe:xx:xx:xx:xx:xx', }, -- Refer to http://fastd.readthedocs.org/en/latest/ to better understand -- what these options do. fastd_mesh_vpn = { -- List of crypto-methods to use. methods = {'salsa2012+umac'}, mtu = 1426, groups = { backbone = { -- Limit number of connected peers to reduce bandwidth. limit = 2, -- List of peers. peers = { peer1 = { key = 'xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx', -- This is a list, so you might add multiple entries. remotes = {'ipv4 "xxx.somehost.invalid" port xxxxxx'}, }, peer2 = { key = 'xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx', -- You can also omit the ipv4 to allow both connection via ipv4 and ipv6 remotes = {'"xxx.somehost2.invalid" port xxxxx'}, }, }, -- Optional: nested peer groups -- groups = { -- backbone_sub = { -- ... -- }, -- ... -- }, }, -- Optional: additional peer groups, possibly with other limits -- backbone2 = { -- ... -- }, }, }, autoupdater = { -- Default branch. Don't forget to set GLUON_BRANCH when building! branch = 'stable', -- List of branches. You may define multiple branches. branches = { stable = { name = 'stable', -- List of mirrors to fetch images from. IPv6 required! mirrors = {'http://1.updates.services.ffhl/stable/sysupgrade'}, -- Number of good signatures required. -- Have multiple maintainers sign your build and only -- accept it when a sufficient number of them have -- signed it. good_signatures = 2, -- List of public keys of maintainers. pubkeys = { 'xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx', -- Alice 'xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx', -- Bob 'xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx', -- Mary }, }, }, }, -- Node roles -- roles = { -- default = 'node', -- list = { -- 'node', -- 'test', -- 'backbone', -- 'service', -- }, -- }, -- Bandwidth limiting simple_tc = { mesh_vpn = { ifname = 'mesh-vpn', -- You may enable it by default here. enabled = false, -- Default upload limit (kbit/s). limit_egress = 200, -- Default download limit (kbit/s). limit_ingress = 3000, }, }, -- Skip setup mode (config mode) on first boot -- setup_mode = { -- skip = true, -- }, }